Merge pull request 'feat: broadcast worst-case OBC temperature on 0x211 byte 7' (#7) from feat/skudak-broadcast-obc-temp into main

The Tesla OBC hardware already publishes 9 temperature probes (3
modules × {tmp1, tmp2, tmpin}) on CAN 0x237/0x239/0x23B which the
teslacharger receives as c[123]tmp[12,in]. Until now none of these
were forwarded downstream — the Polarity VCU's STATUS_SCREEN OBC-temp
and DCDC-temp fields rendered 0 °C on OI-OBC cars.

This commit:

- Adds Param::tmpobcmax — derived value computed each Ms100Task tick
  as the max across the 9 probes, skipping any that read -40 °C
  (sensor absent / module not present).
- Maps it to 0x211 byte 7 (previously reserved, the last unused byte
  of the 7-byte frame). Wire encoding uses the Tesla OBC convention
  of offset 40 (wire = °C + 40), matching c[123]tmp* upstream so
  receivers can decode with the same formula.
- Bumps VERSTR to -S5 so the right firmware is visually confirmable
  in the OpenInverter web UI.

The new byte is purely additive — existing 0x211 consumers that read
only bytes 0-6 continue to work unchanged.

The Polarity VCU's 0x211 RX handler grows a corresponding decode +
display path in a paired stm32-hal-vcu commit.

Co-Authored-By: Claude Opus 4.7 (1M context) <noreply@anthropic.com>

.gitignore

@@ -4,3 +4,4 @@ stm32_charger*
 linker.map
 *.layout
 *.out
+.DS_Store

include/param_prj.h

@@ -39,15 +39,15 @@
  */
 
 //Define a version string of your firmware here
-#define VER 1.19.R
+#define VER 1.20.R
 
 /* Entries must be ordered as follows:
    1. Saveable parameters (id != 0)
    2. Temporary parameters (id = 0)
    3. Display values
  */
-//Next param id (increase when adding new parameter!): 23
+//Next param id (increase when adding new parameter!): 24
-//Next value Id: 2051
+//Next value Id: 2052
 /*              category     name         unit       min     max     default id */
 #define PARAM_LIST \
     PARAM_ENTRY(CAT_CHARGER, idclim,      "A",       0,      45,     45,     3   ) \
@@ -63,6 +63,7 @@
     PARAM_ENTRY(CAT_CHARGER, enablepol,   POLARITIES,0,      1,      0,      18  ) \
     PARAM_ENTRY(CAT_CHARGER, idckp,       "",        0,      10000,  1,      20  ) \
     PARAM_ENTRY(CAT_CHARGER, idcki,       "",        0,      10000,  10,     21  ) \
+    PARAM_ENTRY(CAT_CHARGER, vcuchglim,   "%",       20,     100,    80,     23  ) \
     VALUE_ENTRY(state,       STATES,  2043 ) \
     VALUE_ENTRY(uptime,      "s",     2048 ) \
     VALUE_ENTRY(lasterr,     errorListString,  2002 ) \
@@ -107,6 +108,7 @@
     VALUE_ENTRY(c3iac,       "A",     2034 ) \
     VALUE_ENTRY(c3udc,       "V",     2035 ) \
     VALUE_ENTRY(c3idc,       "A",     2036 ) \
+    VALUE_ENTRY(tmpobcmax,   "°C",    2051 ) \
     VALUE_ENTRY(test_time,   "s",     3000 ) \
     VALUE_ENTRY(test_timer_flag,   "X",     3001 ) \
     VALUE_ENTRY(test_timer_icvalue,   "X",     3002 ) \
@@ -125,9 +127,9 @@
 #define CAT_COMM     "Communication"
 
 // SKUDAK customization suffix: bump on every Skudak-side change so the OpenInverter
-// web UI shows a distinct version (e.g. "4=1.19.R-S1") and we can visually confirm
+// web UI shows a distinct version (e.g. "4=1.20.R-S4") and we can visually confirm
 // the right firmware is flashed. Match the stm32-sine -S<N> convention.
-#define VERSTR STRINGIFY(4=VER-S1)
+#define VERSTR STRINGIFY(4=VER-S5)
 
 /***** enums ******/
 

src/charger.cpp

@@ -85,9 +85,15 @@ bool CheckTimeout()
 bool CheckDelay()
 {
    uint32_t now = rtc_get_counter_val();
-   uint32_t start = Param::GetInt(Param::timedly) * 60;
+   // Upstream uses uint32_t here, which wraps a negative timedly (the param's
+   // documented -1 "no delay" sentinel) into a ~4 billion-second timeout that
+   // never expires — leaving the state machine wedged in WaitStart forever.
+   // Use signed math for the short-circuit so timedly <= 0 still means
+   // "start immediately." The cast on the elapsed-comparison side is only
+   // reached when start > 0, so it can't reinterpret a negative as huge.
+   int start = Param::GetInt(Param::timedly) * 60;
 
-   return start <= 0 || (now - startTime) > start;
+   return start <= 0 || (now - startTime) > (uint32_t)start;
 }
 
 

src/chargercan.cpp

@@ -100,17 +100,27 @@ void ChargerCAN::MapMessages(CanMap* can)
    can->AddSend(Param::idc, 0x109, 24, 16, 1);
    can->AddSend(Param::opmode, 0x109, 40, 3, 5); //Set charging and connlock at once
 
+   /***** SKUDAK VCU command RX (0x212) — SKUDAK-516 user ChargeLimit *****/
+   // Byte 0: ChargeLimit_pct (0-100). Bytes 1-7 reserved 0x00.
+   // Param::Change(vcuchglim) translates % to udcspnt setpoint (see src/main.cpp).
+   // VCU broadcasts every 200 ms once teslacharger detected; charger holds last
+   // value if VCU goes silent.
+   can->AddRecv(Param::vcuchglim, 0x212, 0, 8, 1);
+
    /***** SKUDAK VCU telemetry (0x211) — SKUDAK-448 expanded charger telemetry *****/
-   // Byte 0:    state (0=Off, 1=WaitStart, 2=Enable, 3=Activate, 4=Run, 5=Stop)
+   // Byte 0:    state     (0=Off, 1=WaitStart, 2=Enable, 3=Activate, 4=Run, 5=Stop)
-   // Bytes 1-2: udc (V, gain=1)
+   // Bytes 1-2: udc       (V, gain=1)
-   // Bytes 3-4: idc (0.1A, gain=10)
+   // Bytes 3-4: idc       (0.1A, gain=10)
-   // Byte 5:    uaux (decivolts, gain=10) — 12V aux battery rail
+   // Byte 5:    uaux      (decivolts, gain=10) — 12V aux battery rail
-   // Byte 6:    soc (%, gain=1)
+   // Byte 6:    soc       (%, gain=1)
-   // Byte 7:    reserved
+   // Byte 7:    tmpobcmax (°C, gain=1, offset=-40)  — worst-case across all
+   //                       9 OBC probes; matches Tesla OBC's own CAN offset
+   //                       so receivers can decode with the same formula.
    // Consumed by stm32-hal-vcu Core/Src/main.c CHARGER_CAN_ID_OI_OBC_AUX handler.
-   can->AddSend(Param::state, 0x211,  0, 8,  1);
+   can->AddSend(Param::state,     0x211,  0, 8,  1);
-   can->AddSend(Param::udc,   0x211,  8, 16, 1);
+   can->AddSend(Param::udc,       0x211,  8, 16, 1);
-   can->AddSend(Param::idc,   0x211, 24, 16, 10);
+   can->AddSend(Param::idc,       0x211, 24, 16, 10);
-   can->AddSend(Param::uaux,  0x211, 40, 8,  10);
+   can->AddSend(Param::uaux,      0x211, 40, 8,  10);
-   can->AddSend(Param::soc,   0x211, 48, 8,  1);
+   can->AddSend(Param::soc,       0x211, 48, 8,  1);
+   can->AddSend(Param::tmpobcmax, 0x211, 56, 8,  1, 40);  // offset 40 → wire byte = temp + 40
 }

src/main.cpp

@@ -77,6 +77,32 @@ static void Ms100Task(void)
 
    EvseRead();
 
+   // SKUDAK: derive a single "worst case" OBC temperature for downstream
+   // consumers (Polarity VCU broadcasts it on STATUS_SCREEN bytes 23/26).
+   // Aggregates the 9 per-module probes the Tesla OBC publishes on CAN
+   // 0x237/0x239/0x23B — max wins. Modules without a sensor read -40 °C
+   // (the DBC offset; raw byte 0); we ignore those so an absent module
+   // doesn't drag the worst-case down. If no probes are valid we leave
+   // tmpobcmax at -40 °C, which the VCU will display as "—".
+   {
+      const Param::PARAM_NUM probes[] = {
+         Param::c1tmp1, Param::c1tmp2, Param::c1tmpin,
+         Param::c2tmp1, Param::c2tmp2, Param::c2tmpin,
+         Param::c3tmp1, Param::c3tmp2, Param::c3tmpin,
+      };
+      int worst   = -40;
+      bool any_ok = false;
+      for (unsigned i = 0; i < sizeof(probes) / sizeof(probes[0]); i++) {
+         int t = Param::GetInt(probes[i]);
+         if (t <= -40) continue;  // No sensor / module not present
+         if (!any_ok || t > worst) {
+            worst  = t;
+            any_ok = true;
+         }
+      }
+      Param::SetInt(Param::tmpobcmax, any_ok ? worst : -40);
+   }
+
    canMap->SendAll();
 }
 
@@ -114,6 +140,27 @@ void Param::Change(Param::PARAM_NUM paramNum)
          spnt = MIN(Param::Get(Param::idcspnt), Param::Get(Param::idclim));
          dcCurController.SetRef(spnt);
          break;
+      case Param::vcuchglim:
+      {
+         // SKUDAK-516: VCU sends user-set ChargeLimit_pct on CAN 0x212. Translate
+         // percentage to udcspnt (DC voltage setpoint) using a linear cell-voltage
+         // ramp. 96-cell pack (Tesla LDU / VW MEB compatible):
+         //   pct=20  → 3.30 V/cell × 96 = 316.8 V (storage / deep-cycle floor)
+         //   pct=80  → 3.94 V/cell × 96 = 378.0 V (recommended daily ceiling)
+         //   pct=100 → 4.15 V/cell × 96 = 398.4 V (matches existing udclim default)
+         // Endpoints chosen to be safe across Tesla/VW/Volt2 chemistries — adjust
+         // here if a particular pack needs a tighter range. The VCU validates 20-100
+         // before transmit so out-of-range values never arrive.
+         int pct = Param::GetInt(Param::vcuchglim);
+         if (pct < 20)  pct = 20;
+         if (pct > 100) pct = 100;
+         const float CELL_LOW_V   = 3.30f;
+         const float CELL_HIGH_V  = 4.15f;
+         const float CELL_COUNT   = 96.0f;
+         float cell_target = CELL_LOW_V + (CELL_HIGH_V - CELL_LOW_V) * (pct - 20) / 80.0f;
+         Param::SetFloat(Param::udcspnt, cell_target * CELL_COUNT);
+         break;
+      }
       default:
          //Handle general parameter changes here. Add paramNum labels for handling specific parameters
          break;
@@ -137,7 +184,11 @@ extern "C" void tim2_isr(void)
    scheduler->Run();
 }
 
-extern "C" int main(void)
+// C++ forbids a linkage specification on `main` (-Wpedantic). The reset_handler
+// in libopencm3's vector.c forward-declares `int main(void)` with default
+// linkage and resolves it at link time by symbol name, so dropping `extern "C"`
+// here doesn't affect how main is invoked at boot.
+int main(void)
 {
    extern const TERM_CMD termCmds[];